New Material Can Store Solar Energy During the Day and Release it Later as Heat

A New Way to Store Solar Heat

The layer-by-layer solar thermal fuel polymer film comprises three distinct layers (4 to 5 microns in thickness for each). Cross-linking after each layer enables building up films of tunable thickness.

Engineers from MIT have developed a new material that could harvest sunlight by day and release heat on demand hours or days later.

Imagine if your clothing could, on demand, release just enough heat to keep you warm and cozy, allowing you to dial back on your thermostat settings and stay comfortable in a cooler room. Or, picture a car windshield that stores the sun’s energy and then releases it as a burst of heat to melt away a layer of ice.

According to a team of researchers at MIT, both scenarios may be possible before long, thanks to a new material that can store solar energy during the day and release it later as heat, whenever it’s needed. This transparent polymer film could be applied to many different surfaces, such as window glass or clothing.

Although the sun is a virtually inexhaustible source of energy, it’s only available about half the time we need it — during daylight. For the sun to become a major power provider for human needs, there has to be an efficient way to save it up for use during nighttime and stormy days. Most such efforts have focused on storing and recovering solar energy in the form of electricity, but the new finding could provide a highly efficient method for storing the sun’s energy through a chemical reaction and releasing it later as heat.

The finding, by MIT professor Jeffrey Grossman, postdoc David Zhitomirsky, and graduate student Eugene Cho, is described in a paper in the journal Advanced Energy Materials. The key to enabling long-term, stable storage of solar heat, the team says, is to store it in the form of a chemical change rather than storing the heat itself. Whereas heat inevitably dissipates over time no matter how good the insulation around it, a chemical storage system can retain the energy indefinitely in a stable molecular configuration, until its release is triggered by a small jolt of heat (or light or electricity).

MIT Solar Fuel A New Way to Store Solar Heat

In the researchers’ platform for testing macroscopic heat release, a heating element provides sufficient energy to trigger the solar thermal fuel materials, while an infrared camera monitors the temperature. The charged film (right) releases heat enabling a higher temperature relative to the uncharged film (left).

Molecules with two configurations

The key is a molecule that can remain stable in either of two different configurations. When exposed to sunlight, the energy of the light kicks the molecules into their “charged” configuration, and they can stay that way for long periods. Then, when triggered by a very specific temperature or other stimulus, the molecules snap back to their original shape, giving off a burst of heat in the process.

Such chemically-based storage materials, known as solar thermal fuels (STF), have been developed before, including in previous work by Grossman and his team. But those earlier efforts “had limited utility in solid-state applications” because they were designed to be used in liquid solutions and not capable of making durable solid-state films, Zhitomirsky says. The new approach is the first based on a solid-state material, in this case a polymer, and the first based on inexpensive materials and widespread manufacturing technology.

“This work presents an exciting avenue for simultaneous energy harvesting and storage within a single material,” says Ted Sargent, university professor at the University of Toronto, who was not involved in this research.

Manufacturing the new material requires just a two-step process that is “very simple and very scalable,” says Cho. The system is based on previous work that was aimed at developing a solar cooker that could store solar heat for cooking after sundown, but “there were challenges with that,” he says. The team realized that if the heat-storing material could be made in the form of a thin film, then it could be “incorporated into many different materials,” he says, including glass or even fabric.

To make the film capable of storing a useful amount of heat, and to ensure that it could be manufactured easily and reliably, the team started with materials called azobenzenes that change their molecular configuration in response to light. The azobenzenes can then can be stimulated by a tiny pulse of heat, to revert to their original configuration and release much more heat in the process. The researchers modified the material’s chemistry to improve its energy density — the amount of energy that can be stored for a given weight — its ability to form smooth, uniform layers, and its responsiveness to the activating heat pulse.

MIT Solar Fuel A New Way to Store Solar Heat

A heating element is used to provide sufficient energy to trigger the solar thermal fuel materials, while an infrared camera monitors the temperature. (View full screen to see animation.)

Shedding the ice

The material they ended up with is highly transparent, which could make it useful for de-icing car windshields, says Grossman, the Morton and Claire Goulder and Family Professor in Environmental Systems and a professor of materials science and engineering. While many cars already have fine heating wires embedded in rear windows for that purpose, anything that blocks the view through the front window is forbidden by law, even thin wires. But a transparent film made of the new material, sandwiched between two layers of glass — as is currently done with bonding polymers to prevent pieces of broken glass from flying around in an accident — could provide the same de-icing effect without any blockage. German auto company BMW, a sponsor of this research, is interested in that potential application, he says.

With such a window, energy would be stored in the polymer every time the car sits out in the sunlight. Then, “when you trigger it,” using just a small amount of heat that could be provided by a heating wire or puff of heated air, “you get this blast of heat,” Grossman says. “We did tests to show you could get enough heat to drop ice off a windshield.” Accomplishing that, he explains, doesn’t require that all the ice actually be melted, just that the ice closest to the glass melts enough to provide a layer of water that releases the rest of the ice to slide off by gravity or be pushed aside by the windshield wipers.

The team is continuing to work on improving the film’s properties, Grossman says. The material currently has a slight yellowish tinge, so the researchers are working on improving its transparency. And it can release a burst of about 10 degrees Celsius above the surrounding temperature — sufficient for the ice-melting application — but they are trying to boost that to 20 degrees.

Already, the system as it exists now might be a significant boon for electric cars, which devote so much energy to heating and de-icing that their driving ranges can drop by 30 percent in cold conditions. The new polymer could significantly reduce that drain, Grossman says.

“The approach is innovative and distinctive,” says Sargent, from the University of Toronto. “The research is a major advance towards the practical application of solid-state energy-storage/heat-release materials from both a scientific and engineering point of view.”

The work was supported by a NSERC Canada Banting Fellowship and by BMW.

Reference: “Solid-State Solar Thermal Fuels for Heat Release Applications” by David Zhitomirsky, Eugene Cho and Jeffrey C. Grossman, 23 December 2015, Advanced Energy Materials.
DOI: 10.1002/aenm.201502006

4 Comments on "New Material Can Store Solar Energy During the Day and Release it Later as Heat"

  1. Sankaravelayudhan Nandakumar | January 13, 2016 at 4:34 pm | Reply

    Combined air filter choking detection application to prevent choking and major shut down during combustion:
    Along with delta pressure analysis the filter nozzle melting due to dust blocking can also be prevented.The Italian firm which failed to to have signals during dust blockage and filter nozzle melting problems for such materials can also be embedded with graphical algorithmic representation in operators room.M/S BHEL research Group may carefully note down this aspect for their future designs.
    Thank you MIT Research scholars.
    Sankravelayudhan Nandakumar former Project coordinator,Cape Institute of Technology ,Anna University retired Chief Thermal Engineer,TNEB

  2. Madanagopal.V.C. | January 15, 2016 at 9:57 am | Reply

    Sandwiched between two layers of glass, these solar cells may be analagous to condensors in electricity, where excess current is stored and then released when tapped. Here excess heat is stored and released later on to emit solar current from the material of the solar cell. Thank You.

  3. A great effort I must say. The concept of storing Solar energy and utilizing it later can be of great significance for the upcoming generation and technologies.

  4. Clyde Spencer | April 23, 2021 at 7:41 am | Reply

    An interesting concept, similar to phase-change hand warmers. It has a similar drawback in that instead of the genie providing you with three wishes, you get one wish a day. That is, being a thin film, the capacity for melting windshield ice is probably going to be a one-shot opportunity, until exposed to another cycle of sunlight.

    Something else that immediately comes to mind: If triggered by heat, what is to prevent direct sunlight from heating the window (or if left sitting in the sun in Phoenix) and discharging the heat when not wanted or needed? The same is true with its use in clothes. You need the release of energy to be triggered by cold, NOT by heat. Therefore, it seems to me that there is a major obstacle to using this material for the suggested applications.

Leave a Reply to Sankaravelayudhan Nandakumar Cancel reply

Email address is optional. If provided, your email will not be published or shared.